Sale
Sold Out
Sold Out
Zoom the image with mouse
Diadent D-Lux-Dual Wavelength Cordless LED Curing Light
Rs. 17,250
Rs. 17,500
Subcribe to back in stock notification
Dual Wavelength Cordless LED Curing Light
D-Lux is a new advanced cordless LED curing light. Made from the highest quality aluminum, D-Lux dissipates heat quickly to prevent overheating problem so that it can produce the maximum light intensity safely and consistently. With its lightweight and ergonomic design, D-Lux is easy to use and highly portable.Its battery pack can easily be replaced. Without taking out the battery from the hand-piece completely, the power can be shut off by using the Power switch. With advanced built-in protection circuit modules (to protect over-charging and over- discharging), D-Lux is reliable and safe to use. OLED display panel conveniently indicates battery life and a countdown timer for the next needed charge.
With D-Lux's fast charging system, the battery can be fully charged in 90 minutes. D-Lux also has 5 versatile curing modes for every indication, such as turbo mode, soft start mode and pulse mode. Soft-start mode and pulse mode can reduce the rapid contraction when the composite resin material is being cured by the curing light
Features
• High intensity output of 2,400 mW/cm2 and 10W LED• 360° swivel light probe and silicone ring tip ensure patient comfort
• Broadband spectrum of 385nm~515nm
• Dual-wavelength with 4 LED lamps can efficiently polymerize all dental materials
• Wireless inductive charging system eliminates any potential charging contact problems
• High capacity 2,600 mAh Li-ion battery offers longer battery life and power intensity stability
• Designed ergonomically, the handpiece is light and elegant so it can easily reach all curing sites offering maximum comfort for both patient and clinician
• Designed for comfort, the light probe has an optimal 10 angle to reach all tooth surface even posterior area
• Built-in Light Intensity Measurement Sensor provides peace of mind so clinicians can always verify if the intensity is within normal range
• 5 versatile curing modes allow flexible curing time and power intensity including 1-second curing and Orthodontic curing mode
5 CURING MODES:
- 5 Max: Maximum light intensity output for 5 seconds
- 10 Max: Maximum light intensity output for 10 seconds
- 20 Mid: 70% output of maximum light intensity for 20 seconds
- 20 Soft: An initial 10% output of maximum light intensity that gradually increases to full power in 10 seconds, followed by 10 seconds output at full power.
- 20 Pulse: Pulses every 0.15 seconds for 20 seconds at a maximum light intensity
Light wavelength range:420-490nm
Light intensity: 1,600 mW/cm
Charging time: Approx 1 hr 30 mins
5 CURING MODES:
5 Max: Maximum light intensity output for 5 seconds
10 Max: Maximum light intensity output for 10 seconds
20 Mid: 70% output of maximum light intensity for 20 seconds
20 Soft: An initial 10% output of maximum light intensity that gradually increases to full power in 10 seconds, followed by 10 seconds output at full power.
20 Pulse: Pulses every 0.15 seconds for 20 seconds at a maximum light intensity
Accessories
#4008-1110 Handpiece
#4008-1120 Charger
#4008-1130 Light Probe
#4008-1140 Battery Pack
#4008-1150 Light Protector
#4008-1160 Power Supply (Adapter)
#4008-1161 Power Cord
#4008-1170 Disposable Sheaths (200/Box)
Light intensity: 1,600 mW/cm
Charging time: Approx 1 hr 30 mins
5 CURING MODES:
5 Max: Maximum light intensity output for 5 seconds
10 Max: Maximum light intensity output for 10 seconds
20 Mid: 70% output of maximum light intensity for 20 seconds
20 Soft: An initial 10% output of maximum light intensity that gradually increases to full power in 10 seconds, followed by 10 seconds output at full power.
20 Pulse: Pulses every 0.15 seconds for 20 seconds at a maximum light intensity
Accessories
#4008-1110 Handpiece
#4008-1120 Charger
#4008-1130 Light Probe
#4008-1140 Battery Pack
#4008-1150 Light Protector
#4008-1160 Power Supply (Adapter)
#4008-1161 Power Cord
#4008-1170 Disposable Sheaths (200/Box)
Hand-piece Components Installation
Step 1. Insert the light guide fully into the hand-piece. * For best result, check to see if the light guide is completely inserted into the hand-piece
Step 2. Put the Plastic Protector onto the light guide
Step 3. Turn on the Power Switch button at bottom of the hand-piece.
Charger Installation & Charging Unit
Step 1. Place the charger on a secure flat surface
Step 2. Connect the power cord to the charger power supply
Step 3. Connect charger power supply to the Charger Base
Step 4. Seat the hand-piece into the Charger Base as shown in the picture. * Light indicator on the Charger Base will change from red to blue once the battery is fully charged. If the battery pack is broken or needs to be replaced, light indicator will be blinking red
Step 5. To fully charge the battery, it will take approximately 1.5 hour
Function set up
1. When the light is off on OLED panel, turn on the Power Switch button at the bottom of the hand-piece or press the MODE button to turn on the OLED panel.
2. When MODE button is pressed, OLED Panel will display: 5 Max, 10 Max, 20 Mid, 20 Soft, and 20 Pulse. (See Hand-piece Features for Mode Functions.)
3. When you press the Operation button on the OLED Panel, it will initiate the selected curing mode. When you press the button during operation, the program will stop.
The light intensity output time is displayed on the OLED panel in numbers.
CHARGER FEATURES
1. Charger has one display light indicator and the light indicator is not on unless the hand-piece is seated and connected into the Charger Base.1. Charger has one display light indicator and the light indicator is not on unless the hand-piece is seated and connected into the Charger Base
2. When the hand-piece is seated into the Charger Base, the light indicator will turn red. Light indicator will turn blue once the battery is fully charged. If the battery is not fully charged, light indicator will turn red and charging will begin.
3. When the hand-piece is seated into the Charger Base, light indicator can turn either red or blue. If the light indicator is not turned on, it means the hand-piece is not properly connected to the Charger Base. In this case, the hand-piece should be repositioned and reseated into the Charger Base.
4. If the light indicator is blue, the battery is fully charged. (If the light indicator is blue, it is recommended for users to continue charging the device for about 10 - 20 minutes in order for the device to reach its full capacity.)
5. When the light indicator is blinking red, the hand-piece should be repositioned and reseated into the Charger Base. (If the light indicator continues to blink red after the procedure, the battery may be defective. Do not use this battery again.)
6. If the light indicator does not turn on even when the hand-piece is properly connected and seated, the battery may be defective. The battery should be replaced.
* Due to D-Lux's fast charging system, it is normal for a little heat to be generated during the charging procedure.
2. When the hand-piece is seated into the Charger Base, the light indicator will turn red. Light indicator will turn blue once the battery is fully charged. If the battery is not fully charged, light indicator will turn red and charging will begin.
3. When the hand-piece is seated into the Charger Base, light indicator can turn either red or blue. If the light indicator is not turned on, it means the hand-piece is not properly connected to the Charger Base. In this case, the hand-piece should be repositioned and reseated into the Charger Base.
4. If the light indicator is blue, the battery is fully charged.
(If the light indicator is blue, it is recommended for users to continue charging the device for about 10 - 20 minutes in order for the device to reach its full capacity.)
5. When the light indicator is blinking red, the hand-piece should be repositioned and reseated into the Charger Base. (If the light indicator continues to blink red after the procedure, the battery may be defective. Do not use this battery again.)
6. If the light indicator does not turn on even when the hand-piece is properly connected and seated, the battery may be defective. The battery should be replaced.
* Due to D-Lux's fast charging system, it is normal for a little heat to be generated during the charging procedure.
Cleaning
The device should be cleaned with dry soft wipes.
DO NOT use abrasive material such as scouring powder, organic solvents, or solvent-based cleaning fluids. In case of severe contamination, gently clean the device by using diluted alcohol
DO NOT use pure alcohol-based solutions
Turn off the Power Switch at the bottom of the hand-piece and store the device in the box if it is not to be used for an extended period of time
DO NOT autoclave the hand-piece.
DO NOT autoclave the light guide.
Light emitted by LED can be harmful and should never be directed towards the eyes.
Direct exposure to the light may damage the eyesight.
Storage
Keep away from any place where products may be damaged.
Step 1. Insert the light guide fully into the hand-piece. * For best result, check to see if the light guide is completely inserted into the hand-piece
Step 2. Put the Plastic Protector onto the light guide
Step 3. Turn on the Power Switch button at bottom of the hand-piece.
Charger Installation & Charging Unit
Step 1. Place the charger on a secure flat surface
Step 2. Connect the power cord to the charger power supply
Step 3. Connect charger power supply to the Charger Base
Step 4. Seat the hand-piece into the Charger Base as shown in the picture. * Light indicator on the Charger Base will change from red to blue once the battery is fully charged. If the battery pack is broken or needs to be replaced, light indicator will be blinking red
Step 5. To fully charge the battery, it will take approximately 1.5 hour
Function set up
1. When the light is off on OLED panel, turn on the Power Switch button at the bottom of the hand-piece or press the MODE button to turn on the OLED panel.
2. When MODE button is pressed, OLED Panel will display: 5 Max, 10 Max, 20 Mid, 20 Soft, and 20 Pulse. (See Hand-piece Features for Mode Functions.)
3. When you press the Operation button on the OLED Panel, it will initiate the selected curing mode. When you press the button during operation, the program will stop.
The light intensity output time is displayed on the OLED panel in numbers.
CHARGER FEATURES
1. Charger has one display light indicator and the light indicator is not on unless the hand-piece is seated and connected into the Charger Base.1. Charger has one display light indicator and the light indicator is not on unless the hand-piece is seated and connected into the Charger Base
2. When the hand-piece is seated into the Charger Base, the light indicator will turn red. Light indicator will turn blue once the battery is fully charged. If the battery is not fully charged, light indicator will turn red and charging will begin.
3. When the hand-piece is seated into the Charger Base, light indicator can turn either red or blue. If the light indicator is not turned on, it means the hand-piece is not properly connected to the Charger Base. In this case, the hand-piece should be repositioned and reseated into the Charger Base.
4. If the light indicator is blue, the battery is fully charged. (If the light indicator is blue, it is recommended for users to continue charging the device for about 10 - 20 minutes in order for the device to reach its full capacity.)
5. When the light indicator is blinking red, the hand-piece should be repositioned and reseated into the Charger Base. (If the light indicator continues to blink red after the procedure, the battery may be defective. Do not use this battery again.)
6. If the light indicator does not turn on even when the hand-piece is properly connected and seated, the battery may be defective. The battery should be replaced.
* Due to D-Lux's fast charging system, it is normal for a little heat to be generated during the charging procedure.
2. When the hand-piece is seated into the Charger Base, the light indicator will turn red. Light indicator will turn blue once the battery is fully charged. If the battery is not fully charged, light indicator will turn red and charging will begin.
3. When the hand-piece is seated into the Charger Base, light indicator can turn either red or blue. If the light indicator is not turned on, it means the hand-piece is not properly connected to the Charger Base. In this case, the hand-piece should be repositioned and reseated into the Charger Base.
4. If the light indicator is blue, the battery is fully charged.
(If the light indicator is blue, it is recommended for users to continue charging the device for about 10 - 20 minutes in order for the device to reach its full capacity.)
5. When the light indicator is blinking red, the hand-piece should be repositioned and reseated into the Charger Base. (If the light indicator continues to blink red after the procedure, the battery may be defective. Do not use this battery again.)
6. If the light indicator does not turn on even when the hand-piece is properly connected and seated, the battery may be defective. The battery should be replaced.
* Due to D-Lux's fast charging system, it is normal for a little heat to be generated during the charging procedure.
Cleaning
The device should be cleaned with dry soft wipes.
DO NOT use abrasive material such as scouring powder, organic solvents, or solvent-based cleaning fluids. In case of severe contamination, gently clean the device by using diluted alcohol
DO NOT use pure alcohol-based solutions
Turn off the Power Switch at the bottom of the hand-piece and store the device in the box if it is not to be used for an extended period of time
DO NOT autoclave the hand-piece.
DO NOT autoclave the light guide.
Light emitted by LED can be harmful and should never be directed towards the eyes.
Direct exposure to the light may damage the eyesight.
Storage
Keep away from any place where products may be damaged.
Key features
1.Built-in Light Intensity Measurement Sensor
2.Designed ergonomically
3.High intensity output of 2,400 mW/cm2 and 10W LED
4. 360° swivel ensure patient comfort
5.Broadband spectrum of 385nm~515nm